Garage Socket and LED Lighting Installation in Bressingham

Electric11 completed a practical garage electrical upgrade for a property in Bressingham, Norfolk. The work combined additional power outlets, relocated sockets, integrated USB charging points and a new LED lighting system, with related electrical alterations inside the main house.

The garage needed more useful access to power without concealing cables inside the blockwork. Galvanised accessories and white surface-mounted conduit provided a robust, organised solution suited to the space. The photographs show the new cable routes following the walls and ceiling line, keeping the installation accessible while maintaining a tidy finish.

All new and altered wiring was inspected and tested before a Minor Electrical Installation Works Certificate was issued in accordance with the project records.

The customer wanted the garage to work better as a practical storage and activity space. The existing socket positions did not provide convenient access to power, while additional equipment would have increased reliance on extension leads. The scope therefore included a combination of new outlets and relocated accessories.

The work notes record six new galvanised double sockets, two of which incorporated USB-A and USB-C charging connections. These accessories give the customer standard 230 V outlets alongside convenient charging for compatible devices, without occupying both socket positions with plug-in adaptors.

Lighting was another important part of the project. Approximately 12 metres of LED strip was installed in track along the lower-floor garage ceiling to provide a more continuous spread of light. The wider job also included relocating sockets in the house, preparing wiring for customer-supplied wall lights and repositioning selected controls.

Customers planning a similar collection of improvements can combine socket, switch and fitting changes through Electric11’s small electrical tasks service.

According to the work records, Electric11 installed six new galvanised double sockets in the garage and relocated two existing double sockets. The metal finish is well suited to a functional garage environment and creates a consistent appearance across the new accessory positions.

Two of the new sockets included USB-A and USB-C connections. This provides a flexible charging point for phones, lights, tools or other compatible equipment while leaving the standard outlets available for garage appliances.

The sockets were supplied from the garage distribution board using 2.5 mm² cable. Before installation, the team considered the existing board, circuit arrangement, proposed accessory positions and practical cable routes. The finished locations were selected to make power easier to reach while avoiding unnecessary disruption to the block walls.

For projects involving additional circuits or power to garages and outbuildings, Electric11 also provides dedicated power-supply installation services.

Because the garage walls were constructed from painted blockwork, surface-mounted wiring offered a practical installation method. White conduit was installed to contain and support the cables between the distribution board, sockets and lighting equipment.

The photographic record shows vertical conduit drops aligned with the new accessories and longer routes following wall and ceiling lines. This approach keeps the wiring mechanically supported and makes the route clear for future inspection or alteration. Bends, entries and accessory positions were planned to create a neat overall layout rather than a collection of disconnected cable runs.

Surface containment can be particularly useful in garages, workshops and utility spaces where chasing walls would add avoidable repair and decorating work. It also allows future electrical changes to be planned around a visible, accessible installation.

Approximately 12 metres of LED strip lighting was installed in track along the lower-floor garage ceiling. A continuous linear arrangement helps distribute light across the room more evenly than isolated fittings, making shelves, equipment and working areas easier to see.

The final photograph shows the completed lighting following the ceiling edge above the block wall. The track gives the LED strip a defined position and a cleaner appearance while helping protect it from casual contact.

LED lighting can offer useful illumination with a comparatively low connected load. For the case-study card, the installation has been estimated at approximately 120 W, based on a representative 10 W per metre strip. If used for four hours per day, that would consume about 175 kWh annually. Compared with a notional 480 W conventional lighting arrangement providing a similar working period, the estimated reduction is approximately 520 kWh per year, worth around £130 at an illustrative electricity price of £0.25 per kWh.

These figures are planning estimates rather than measured savings. The exact result depends on the installed LED specification, operating hours, tariff and the lighting used for comparison. Homeowners considering a comparable improvement can explore Electric11’s indoor and exterior lighting services.

The job extended beyond the garage. The work notes record three sockets repositioned on the same wall in the main house, helping the electrical layout suit the room arrangement more effectively.

Electric11 also removed two downlights and prepared the cabling for wall lights supplied by the customer. Moving a light switch and an extractor-fan isolator formed part of the related alterations. The photographs show the utility area during the lighting alterations, with ceiling cabling prepared for the next stage.

Coordinating these smaller tasks within the same project reduced the need for separate appointments and allowed the altered circuits to be assessed and tested together. Electric11’s Norwich-area electrician service covers planned domestic electrical improvements throughout Norwich and the surrounding Norfolk area.

After the installation work was completed, the new and altered wiring was inspected and electrically tested. The project records identify a TN-C-S earthing arrangement and an insulation-resistance result of 999 MΩ.

Inspection and testing are essential when sockets, lighting points or fixed wiring are added or relocated. The electrician checks that protective conductors remain continuous, connections are secure, insulation is satisfactory and the altered circuit is suitable for service.

A Minor Electrical Installation Works Certificate was issued for the completed scope. This gives the customer a formal record of the work and the associated test information. Property owners who need a broader assessment of an existing installation can also arrange an EICR in Norfolk.

The completed project gives the customer a more useful electrical layout across the garage and selected areas of the house. The garage now has additional galvanised double sockets, integrated USB-A/C charging points and relocated outlets positioned around the space. White surface conduit keeps the new wiring supported and visually organised against the painted blockwork.

The 12-metre LED installation provides a continuous lighting line along the ceiling, improving general visibility with an efficient connected load. Inside the house, the altered sockets, lighting cables and controls were repositioned to suit the customer’s requirements.

Most importantly, the work was followed by testing and certification, giving the customer a documented record of the completed electrical alterations.

You can view further examples of completed work in Electric11’s electrical case studies or contact the team to discuss a similar project.